Paint fill DIY

[Siren]

Whats best to use? Model paint or nail polish?

The paint has started coming out of the I20 numbers already and thought id try a DIY job but I cant seem to find a definitive answer.

Ive looked at a few you tube videos and it seems to be 50/50. Im guessing nail polish in case I make a mess of it?

Also will acetone remove the paint out of the other clubs numbering or should I just paint over?

Thanks in advance.

 

[m9wst]

I think people have used both successfully. Personally I used acrylic humbrol model paint - from what i recall they cost about £1.20 per pot.

If you are going to replace the paint though i would recommend removing the rest of the existing paint first before applying the new stuff, I used paint stripper stuff from b&q, left that on the paint i wanted removing for an hour or so, most of it will wipe out, the rest i coaxed out with a cocktail stick/scalpel blade depending on how fiddly it was, once i'd got ALL the paint out i cleaned it with acetone/nail polish remover, then left it to dry properly.

I also found it easier to re apply the paint with a cocktail stick - on my nike method putter where the lettering is tiny - then using a cotton wool pad and some acetone lightly rubbed over it collecting the excess.


There was a thread on here within the last few months...i believe harpo72(?) started it, he had some decent results from what i remember.

 

[palindromicbob]

I have used enamel paint and nail polish with similar results. The polish was easier to work with. 2 or 3 layers finished with a clear coat gave the best results. Nail polish offers a massive choice of colours, is cheap dries quickly and is easy to strip back to redo. I did this purple finish on my clubs. Played them about 8 rounds with no problems with the finish. Stripped back to the original black which I had simply painted over to resell.

 

[m9wst]

Did the numbers on the irons, the i20 and ping bit on my driver, and the sole and nike tick on the putter.

Take your time with it, i rushed my first few attempts and ended up starting again.

 

[harpo_72]

There was a thread on here within the last few months...i believe harpo72(?) started it, he had some decent results from what i remember.

Thank you!
I used model paint, there are lots of options and acetone is a must. Some suggest that using the model paint you get for painting remote control cars is good because it flexes but doesn't crack. What ever you choose take your time and wipe the excess off whilst wet. I had one problem with metallic paint and that was it was too thin and required multiple coats so be aware.. But as stated prepare the surface and remove the old stuff first and clean down with acetone to help the paint bond.

 

[Siren]

Thanks guys much appreciated.

 

[tsped83]

I think people have used both successfully. Personally I used acrylic humbrol model paint - from what i recall they cost about £1.20 per pot.

If you are going to replace the paint though i would recommend removing the rest of the existing paint first before applying the new stuff, I used paint stripper stuff from b&q, left that on the paint i wanted removing for an hour or so, most of it will wipe out, the rest i coaxed out with a cocktail stick/scalpel blade depending on how fiddly it was, once i'd got ALL the paint out i cleaned it with acetone/nail polish remover, then left it to dry properly.

I also found it easier to re apply the paint with a cocktail stick - on my nike method putter where the lettering is tiny - then using a cotton wool pad and some acetone lightly rubbed over it collecting the excess.


There was a thread on here within the last few months...i believe harpo72(?) started it, he had some decent results from what i remember.

I've just copied this verbatim in case I decide to give it a go myself fella, very helpful. How is the finish bearing up on the clubs now? Durable? Thanks

 

[m9wst]

No problem, the finish is good...but...there are a few tiny spots on the iron numbers that need re doing - i guess as its hitting the ball/turf/range mat regularly any weak areas will eventually fall out. My putter however is still good. The longer you leave the paint to dry the better.

 

[3565]

I think people have used both successfully. Personally I used acrylic humbrol model paint - from what i recall they cost about £1.20 per pot.

If you are going to replace the paint though i would recommend removing the rest of the existing paint first before applying the new stuff, I used paint stripper stuff from b&q, left that on the paint i wanted removing for an hour or so, most of it will wipe out, the rest i coaxed out with a cocktail stick/scalpel blade depending on how fiddly it was, once i'd got ALL the paint out i cleaned it with acetone/nail polish remover, then left it to dry properly.

I also found it easier to re apply the paint with a cocktail stick - on my nike method putter where the lettering is tiny - then using a cotton wool pad and some acetone lightly rubbed over it collecting the excess.


There was a thread on here within the last few months...i believe harpo72(?) started it, he had some decent results from what i remember.

Just follow these instructions but above all you need patience.

 

[m9wst]

^ is that your scotty? thats some impressive work in the 3 circles!

 

[3565]

^ is that your scotty? thats some impressive work in the 3 circles!

God I wish, but it was a guy on GolfWRX who did it, but if you got the know how, just shows what CAN be done. The best paint fill I've ever seen.

 

[Siren]

http://t.co/YCW0iDDBez

http://t.co/GoZYho34B4

I had a go using nail varnish. I will do it properly in the not so distant future.

 

[Andy808]

I always use Humbrol model paints. If you find the right model shot there is pretty much any colour you can think of and a few you didn't know existed.
Make sure the area to be painted is level, a fine brush and let the paint flood to the level you want. It will shrink back a bit in the middle giving a professional looking finish that is easy to clean.

 

[Siren]

http://t.co/TIAva18FbU - driver

http://t.co/70hHDPpL9m - Hybrid

My god this is addictive. I think ill get the proper paints and do this properly.

 

[3565]

Tried my driver out the other day.

 

[Siren]

Really nice that one mate. Did you do a base layer of yellow then add the red?

 

[3565]

No, just filled the red in first using a cocktail stick, then did the yellow straight away. Took a while to do it but got there. Might try the base coat idea.